Why Is There No Water in My Toilet Tank? 

Did you just try to flush your toilet, and nothing changed? Look into the tank, and you may see no water inside. Before you worry, rest easy that repairing this problem is usually straightforward. If you can’t figure it out yourself, you can always arrange toilet repair with an experienced plumber. Follow these tips to diagnose and repair the problem of no water in the toilet tank. 

Check the Water Supply 

The first move is to verify that the water is turned on. If you or someone in your household recently performed a toilet repair, you most likely turned off the water first. Did you forget to turn it back on? To find out, turn the water shut-off valve on the wall to the rear of the toilet. If the valve was closed, water should now start refilling the tank. If this fails to work, check the water at your sink or a different plumbing fixture. If nothing spills out from the tap, you might have a bigger water supply issue. Phone your water company to learn more. 

Reposition or Replace the Float Mechanism 

Older toilet designs use a float ball to measure the water level as it rises in the tank. When the ball passes a specific height, the float arm it’s joined to stops the water flow. However, insufficient water could enter the tank if the ball is positioned improperly or the arm is damaged. To adjust the float ball, start by removing the toilet tank cover. Bend the float arm up just a little bit to alter where it sits in the tank. If this doesn’t fix the problem, you might need to replace the whole float mechanism. You should be able to perform this yourself by following the detailed steps that come with the replacement parts, or you can employ a plumber for help. Just realize that float balls are old toilet systems. You may enjoy improved reliability and efficiency if you upgrade the existing tank components or replace the toilet entirely. 

Adjust the Fill Valve 

Newer toilets use a float cup in place of a float ball, coupled with a fill valve and water level rod. There may be no water in the toilet tank because the valve has slipped out of place or become plugged. Here are techniques to consider: 

• Adjust the fill valve: Look inside the toilet and locate the fill valve on top of a vertical tube device on the left side of the tank. Ensure it’s secure and evenly attached to the tube. Then, change the water level. More modern toilets have an adjustment knob you can turn with your hand, while older designs may require you to loosen an adjustment screw with a flathead screwdriver. Flush the toilet and make it possible for the tank refill to verify the water level. Adjust it until the water comes to {about|approximately|roughly]] one inch below the top of the overflow tube. 
• Clean the fill valve: Mineral buildup and other gunk might be covering the valve and keeping your toilet from filling. Turn off the water behind the toilet and remove the fill cap. Then, gradually turn the water back on, cupping your hand over the valve to block water from spraying all over the place. After several seconds, turn the water back off. Finally, wash the fill cap to remove hard water buildup. If the cap is broken, buy a new one. 
• Clean the valve tube: The tube below the fill valve could also be clogged. Shut off the water and take away the valve hardware. Then, insert a slim bottle brush or wire down the tube. Turn the water back on slightly to flush away the junk. Replace the valve hardware and flush the toilet to check your adjustments. 

Repair or Replace the Trip Assembly 

If you’ve followed the steps above without positive results, the last possibility is a broken trip assembly. This part links the flush handle to the tank. If it’s not working or positioned improperly, the flush cycle may not complete, leaving the tank void. Remove the toilet tank lid and examine the trip assembly attached to the handle. If it’s out of place, reposition it. If the assembly is crooked, worn or busted, replace it. Whether you complete the job yourself or leave it to a plumber, this easy repair should get your toilet tank filled with water again. 

Schedule Toilet Repair Today 

You can’t go long without a working toilet, so reach out to [Company name] to schedule a toilet repair. We can figure out why your toilet isn’t filling and recommend the correct fix. If your plumbing fixture is old and worn out, our team can install a high-efficiency toilet in your bathroom. Be assured that every plumbing repair and replacement we conduct is backed by a 100% satisfaction guarantee. To schedule an evaluation from one of our licensed professionals, please call your community Service Experts Heating, Air Conditioning & Plumbing office today.